RTM and Infusion

RTM and Infusion

RTM and Infusion

Preferred by the world’s leading composites parts manufacturers Poliya’s Infusion / RTM type resins have low viscosity, excellent fiber wet-out and flow properties which makes them ideal resins for marine applications, wind turbine blades and construction applications. Polipol 3382, with high HDT value and Polipol 3567, with minimal shrinkage are resins for RTM applications in vehicle parts, water slide productions.

Polives 702 vinyl ester resin is preferred for infusion applications for boats, yacht, wind turbine blades productions and has high hydrolytic resistance and high mechanical properties.

RTM production method allows for high quality GRP parts on both surfaces.

RTM and Infusion

Preferred by the world’s leading composites parts manufacturers Poliya’s Infusion / RTM type resins have low viscosity, excellent fiber wet-out and flow properties which makes them ideal resins for marine applications, wind turbine blades and construction applications. Polipol 3382, with high HDT value and Polipol 3567, with minimal shrinkage are resins for RTM applications in vehicle parts, water slide productions.

Polives 702 vinyl ester resin is preferred for infusion applications for boats, yacht, wind turbine blades productions and has high hydrolytic resistance and high mechanical properties.

Water Park Slides

Wind Turbine Blades

Marine

Complex GRP Parts

Demolding Large Truck Hood from RTM Mold

Large RTM Parts

SONRAKİ ÖNCEKİ
  •  
  • Product Description
  • Chemical Structure
  • Available Modifications
  • Viscosity
  • Monomer Content
  • Gel Time
  • Tensile Strength
  • Elongation at Break, Tensile
  • Flexural Strength
  • HDT [0,45 MPa]
  • Barcol Hardness, 934
  • Volumetric Shrink
  • Remarks
  • Highlights
  • Primary Usages
  • Polipol 339-I

    New
  • GRP type polyester
  • Ortho
  • 500-700
  • 35-38
  • 12-14
  • 65
  • 2
  • 145
  • 82
  • 47
  • 8,0
  • OT1 , OT2
  • - Good mechanical properties
    - Optimal demolding time
    - Good fiber wet-out
    -Low viscosity
  • RTM parts for automotive , air conditioner duct, roof mounted AC units.
  • Polipol 334-S

  • RTM / Infusion type polyester
  • ISO
  • 180-200
  • 41-44
  • 24-26
  • 69
  • 2,5
  • 139
  • 105
  • 46
  • 8,5
  • OT1 , OT3
  • - Good mechanical properties
    - Optimal demolding time
    - Good fiber wet-out
    -High filler acceptance
    - Low viscosity
  • RTM parts for automotive, water park slides, infusion, roof mounted AC units.
  • Polipol 3650-A

    New
  • Low viscosity, pre-accelerated, infusion type polyester
  • Ortho
  • 140-180
  • 44-47
  • 60-70
  • 70
  • 3,4
  • 135
  • 90
  • 46
  • 6,8
  • OT1 , OT4
  • - Preaccelerated
    - Long gel times available
    - Rapid barcol development
    - Easy and good fiber wetting
  • Composite parts production for marine and wind turbine industries with infusion production method
  • Polipol 3469-I

    New
  • GRP type polyester
  • DCPD
  • 200-250
  • 39-42
  • 18-20
  • 70
  • 2,5
  • 120
  • 85
  • 44
  • 6,0
  • OT1 , OT2
  • - Good mechanical properties
    - High surface quality
    - Good fiber wet-out
    - High filler acceptance
    - Low viscosity
  • RTM parts for automotive, water park slides, infusion, roof mounted AC units.

Resin Infusion Application

Infusion production method recommended for applications like production of marine vehicles and wind turbine blades. It is also useful for the automotive industry in production of low volume parts. Primary purpose is cutting down VOC emissions with high glass fiber ratios of up to 70% and homogeneous distribution of resin through out the part body without air entrapment. Composite parts produced with the infusion method have exceptional mechanical strength.

 

Resin Infusion Products

Both Polives 701-TA skincoat and Polives 702 Infusion type vinyl ester resins are recommended for infusion.

Silicone Membrane System

L–RTM and Infusion resins can be used with vacuum bags and/or reusable silicone membranes.

RTM - Resin Transfer Molding

Composite production with RTM method has the following advantages: good surface appearance on both sides, low workmanship, better dimensional stability, lower styrene emission, high productivity. Because of these properties, it is an ideal method for the production of vehicle parts with or without gelcoat. RTM production steps:


① Apply mold release agent on mold surface
② Apply a gelcoat film of 500-800 microns
③ Lay down reinforcement material on cured (but tacky) gelcoat
④ Close upper mold
⑤ Apply vacuum to seal mold
⑥ Apply vacuum inside the mold if needed
⑦ Check peroxide ratio and equipment pressure
⑧ Inject resin into the mold
⑨ Stop injecting when resin capacity is reached
⑩ Demold the composite part after resin finishes curing

 

RTM and Light RTM production provides a faster composite part production rate with shorter cycle time compared to hand lay-up or spray-up production methods. Incorporation of heating-cooling systems to molds will also speed up production rates.

Packing Types

You can choose any package type suitable for your production system or you can get further information from our sales department regarding container options.

Modification Description

  • FR   Filled flame retardant
  • D*   Filled (*with filler content)
  • T Thixotropic (no sagging)
  • A Cobalt preaccelerated
  • ABP Amine preaccelerated
  • UV UV Curing
  • L   UV light stabilized
  •   I Lower viscosity
  •   V Higher viscosity
  •   LSE   LSE (low styrene emission)
  •   H* Gel time customized (at room temperature) * minutes
  • H40 Optimized for summer season. Gel time (at room temperature) 40 minutes.
  • H20 Optimized for winter season. Gel time (at room temperature) 20 minutes.
  •   COLOR   White or custom color options

Gelcoat Customizations
Polijel gelcoat table descriptions and modifications.

  • Spray Application (airless preferred)
  • Brush or Roller Application
  • Color Option: White colored
  • Color Option: Light colored (pastel)
  • Color Option: PRO colored

Production Quantity Depending on Process (parts/year)
Regardless of product dimension and complexity..

    Contact Us

    * By sending this form I agree to be contacted based on my message and that I may be contacted in the future in accordance with IAI’s privacy policy.