RTM and Infusion

Preferred by the world's leading composites parts manufacturers Poliya's Infusion / RTM type resins have low viscosity, excellent fiber wet-out and flow properties which makes them ideal resins for marine applications, wind turbine blades and construction applications. Polipol 3382, with high HDT value and Polipol 3567, with minimal shrinkage are resins for RTM applications in vehicle parts, water slide productions. 

Polives 702 vinyl ester resin is preferred for infusion applications for boats, yacht, wind turbine blades productions and has high hydrolytic resistance and high mechanical properties. 

Döküm Tipi RTM production method allows for high quality GRP parts on both surfaces.
  •  
  • Product Description
  • Technical Data Sheets
  • Safety Data Sheets
  • Chemical Structure
  • Available Modifications
  • Viscosity (cps)
  • Monomer Content (%)
  • Gel Time (min)
  • Tensile Strength (MPa)
  • Elongation at Break,Tensile (%)
  • Flexural Strength (MPa)
  • HDT [0,45 MPa] (°C)
  • Barcol Hardness, 934 (Barkol)
  • Volumetric Shrinkage (%)
  • Remarks
  • Highlights
  • Primary Usages
  • Polipol 332
  • RTM type polyester
  • PDF
  • PDF
  • ORTO
  • 200-250
  • 41-44
  • 12-14
  • 62
  • 2
  • 138
  • 70
  • 44
  • 8,2
  • OT1 , OT7
  • - Low viscosity
    - Optimum price-performance balance
    - Good fiber wetting
  • Industrial RTM parts.
  • Polipol 336
  • RTM type polyester
  • PDF
  • PDF
  • ORTO
  • 250-350
  • 36-39
  • 12-16
  • 60
  • 2.6
  • 120
  • 83
  • 48
  • 8,2
  • OT1 , OT2
  • - Good mechanical properties
    - Optimal demolding time
    - Good fiber wet-out
    - High filler acceptance
    - Low viscosity
  • RTM parts for automotive, water park slides, infusion, roof mounted AC units.
  • Polipol 3382
  • RTM / Infusion type high HDT polyester
  • PDF
  • PDF
  • ISO/NPG
  • 300-350
  • 40-43
  • 13-17
  • 75
  • 2.6
  • 140
  • 115
  • 48
  • 8,7
  • OT1 , OT2
  • - Excellent HDT, Tg and mechanical properties
    - Short demolding time
    - MAN Nuremberg Lab 3F approved
  • High temperature resistant RTM, VARTM parts.
  • Polipol 3567
  • RTM / Infusion type low shrink polyester
  • PDF
  • PDF
  • DCPD
  • 180-210
  • 37-40
  • 20-22
  • 69
  • 2.6
  • 122
  • 85
  • 44
  • 6
  • OT1 , OT2
  • - Special DCPD structure
    - Low volumetic shrinkage
    - High surface quality on finished part
    - Excellent fiber wet-out
    - High filler acceptance
  • High quality surface, automotive parts, construction industry.
  • Polipol 3387-ZERO
  • ZERO System / RTM infusion type zero shrink polyester
  • PDF
  • PDF
  • DCPD
  • 300-350
  • 39-42
  • 13-17
  • 62
  • 2,4
  • 124
  • 115
  • 44
  • N/A
  • OT1 , OT2
  • - Zero shrinkage
    - Superior surface appearance on finished part
    - Fast demolding time
  • RTM, VARTM parts for automotive.
  • Polipol 3876
  • Flame retardant clear polyester
  • PDF
  • PDF
  • HET/ISO
  • 300-350
  • 37-40
  • 26-28
  • 55
  • 2,8
  • 105
  • 81
  • 42
  • 8,5
  • OT1 , OT2
  • - Fire retardant
    - Good fiber wet-out
    - BC 476 Part 7 Class 2
    - High ATH ratio
  • RTM productions which require flame retardancy.
  • Polives 702
  • RTM / Infusion type vinyl ester
  • PDF
  • PDF
  • VE
  • 200-250
  • 43-45
  • 28-32
  • 76
  • 5
  • 155
  • 102
  • 36
  • 7,7
  • OT1 , OT5
  • - Excellent chemical and mechanical properties
    - Superior hydrolytic resistance
    - Excellent fiber wet-out
    - Lloyd's Register approved
  • Infusion for marine, military and defense applications, wind turbine blades.
  • Polives 711-I
  • RTM / Infusion type high performance vinyl ester
  • PDF
  • PDF
  • VE
  • 180-200
  • 37-40
  • 28-32
  • 78
  • 5,5
  • 154
  • 116
  • 36
  • 8
  • OT1 , OT5
  • - High HDT
    - Excellent hydrolytic and chemical resistance
    - Excellent mechanical properties
    - Excellent fiber wet-out
    - Low viscosity
  • Infusion for marine, military and defense applications, wind turbine blades.

Resin Infusion Application

Infusion production method recommended for applications like production of marine vehicles and wind turbine blades. It is also useful for the automotive industry in production of low volume parts. Primary purpose is cutting down VOC emissions with high glass fiber ratios of up to 70% and homogeneous distribution of resin through out the part body without air entrapment. Composite parts produced with the infusion method have exceptional mechanical strength. 

Resin Infusion Products 

Both Polives 701-TA skincoat and 

Polives 702 Infusion type vinyl ester 

resins are recommended for infusion. 

Silicone Membrane System 

L–RTM and Infusion resins can 

be used with vacuum bags and/or 

reusable silicone membranes. 

Step by step infusion guide 

Please check out our web site for application process steps. 

RTM - Resin Transfer Molding

Composite production with RTM method has the following advantages: good surface appearance on both sides, low workmanship, better dimensional stability, lower styrene emission, high productivity. Because of these properties, it is an ideal method for the production of vehicle parts with or without gelcoat. 

RTM production steps: 

① Apply mold release agent on mold surface 

② Apply a gelcoat film of 500-800 microns 

③ Lay down reinforcement material on cured (but tacky) gelcoat 

④ Close upper mold 

⑤ Apply vacuum to seal mold 

⑥ Apply vacuum inside the mold if needed 

⑦ Check peroxide ratio and equipment pressure 

⑧ Inject resin into the mold 

⑨ Stop injecting when resin capacity is reached 

⑩ Demold the composite part after resin finishes curing 

RTM and Light RTM production provides a faster composite part production rate with shorter cycle time compared to hand lay-up or spray-up production methods.

Incorporation of heating-cooling systems to molds will also speed up production rates. 

Packing Types

You can choose any package type suitable for your production system or you can get further information from our sales department regarding container options.

Contact Sales

  • 25.000 kg
    ISO Tank Container
    Optional Steam heating line Optional Long term renting

  • 18 Kg
    Pail

  • 20 Kg
    Bucket

  • 230 Kg
    Barrel

  • 230 Kg
    Recond. Barrel

  • 1.100 Kg
    IBC

  • 1.100 Kg
    Recond. IBC

Modification Description

  • FR   Filled flame retardant
  • D*   Filled (*with filler content)
  • T Thixotropic (no sagging)
  • A Cobalt preaccelerated
  • ABP Amine preaccelerated
  • UV UV Curing
  • L   UV light stabilized
  •   I Lower viscosity
  •   V Higher viscosity
  •   LSE   LSE (low styrene emission)
  •   H* Gel time customized (at room temperature) * minutes
  • H40 Optimized for summer season. Gel time (at room temperature) 40 minutes.
  • H20 Optimized for winter season. Gel time (at room temperature) 20 minutes.
  •   COLOR   White or custom color options

Gelcoat Customizations
Polijel gelcoat table descriptions and modifications.

  • Spray Application (airless preferred)
  • Brush or Roller Application
  • Color Option: White colored
  • Color Option: Light colored (pastel)
  • Color Option: PRO colored

Production Quantity Depending on Process (parts/year)
Regardless of product dimension and complexity..

İlk sen haberdar ol!
Poliya’nın güncel haberlerinden ve yeni ürünlerinden haberdar olmak ister misiniz?
İzin ver Daha Sonra
x

Haberlerden Geri Kalmayın

En son haberlerimizden ve ürünlerimizden ilk haberdar olmak için lüten aşağıdaki alanları doldurunuz..